Monoprice 3d Printer Software

by

Printer

  • What do the different settings in Cura do?

  • MK1 3D Printer Leveling

  • Why are my layers misaligned?

  • Why does the exterior of my print look 'stringy'?

  • Why is the infill 'stringy'?

  • How To Setup Cura Software

  • What do I do if my printer stops extruding mid-print?

  • What do I do if my printer's nozzle is clogged?

  • Why are my layers misaligned?

  • Why is my printer not reading my SD card?

  • How do I set up my MP Full Enclosed Dual Extruder’s Wifi Connection?

  • How do I set up the MP Voxel Printer’s Wifi Connection?

  • How do I set up the MP Voxel Printer’s Ethernet Connection?

  • Commonly Used Terms

  • Why am I still getting inconsistent layers after leveling the bed on the Maker Select V2 and Plus

  • Dissembling the Mini Select V2 E3D Extruder Assembly

  • Build Plate Adhesion Tips

  • Clogs

  • Dissembling the MP10 and MP10 Mini Extruder Assembly

  • Unclogging the MP Mini Delta

  • Disassembling the extruder on the Monoprice Maker Ultimate

  • MP Cadet Help Guide

Solutions to problems you may run into with your 3D Printer.

Monoprice 3d Printer Software Iifp

  • How do I set up the MP Voxel Printer’s Ethernet Connection?

    The MP Voxel 3D printer’s main printing methods are; Wi-Ficonnection, Ethernet, or Flash Drive. To print over Ethernet, you willwant to do the following steps: Be sure the MP Voxel is plugged intot...

  • MK1 3D Printer Leveling

    The MK1 3D Printer offset correction for the z-axis is not absolute,it is relative. This means if the z-axis offset is currently set to-0.40 and you go to the leveling menu and make adjustments, tha...

  • How do I set up the MP Voxel Printer’s Wifi Connection?

    The MP Voxel 3D printer’s main printing method is over a Wi-Ficonnection. To do this you would need to have a 2.4Ghz Band Network.The MP Voxel will not connect to any other network band and mayrequ...

  • How do I set up my MP Full Enclosed Dual Extruder’s Wifi Connection?

    The MP Full Enclosed Dual Extruder is different from Monoprice’sother 3D Printers as it does not connect to your existing Wi-Fi butinstead creates its own network that will be used to connect to the...

  • Why is my printer not reading my SD card?

    If the SD card is not recognized on the printer or if the files arenot reading, it could be an issue with the actual card itself. Thefirst thing we recommend checking is that none of the print files...

  • Why are my layers misaligned?

    The gears and belts that make up a printer's X and Y-axis can weardown over time. This can cause gears to skip and cause the printer tolose its place. It is good to always lubricate metal-on-metal p...

  • What do I do if my printer's nozzle is clogged?

    The most common way to clean out a clogged nozzle is by inserting awire through the print head to help push any stuck filament out. Twotypes of wire can be used here, 0.35mm thick piano wire or 0.28...

  • What do I do if my printer stops extruding mid-print?

    While printing, there is a motor that pushes filament into theextruder head. If you have your feed rate set too high, it may try toextrude more filament than can possibly pass through the nozzleope...

  • Why is the infill 'stringy'?

    The main culprit for the internal supports of your print being stringywould be the thickness of the layers put down into the infill. You canincrease this setting in Cura under Fill settings. The mos...

  • Why does the exterior of my print look 'stringy'?

    Retraction is the main factor in why prints will have small strings offilament between open spaces. When the nozzle head moves over openspace of the bed to go to another portion of the print, the pr...

Monoprice 3d Printer Software Download

Monoprice 3d printer software cura

Monoprice Iiip 3d Printer Software

Monoprice MP Select Mini 3D Printer V2 Black (Open Box) BEST ANSWER: I own both and I would say the Delta Mini is best if you want to print quickly and easily with not much tinkering. The Select Mini requires bed leveling and will eventually need you to do a gantry support modification as it is only supported on one side. Thank you for purchasing this 3D printer from Monoprice! This printer features a single extruder, which is capable of printing in PLA, ABS, and other materials. You can print from a Windows® or Mac® PC using a USB connection or can print from 3D model files stored on a microSD™ card, without the need for a PC connection of any kind. Cura Slicing Software for Mac® OS X® v3.3.0 (Mar 26, 2019) Wiibuilder Slicing Software for Windows v2.0.6.4 (Jan 20, 2020) WiiBuilder Slicing Software v1.5.7.7 (Mar 26, 2019).